Water guide

How does sedimentation work in water treatment?

In this guide
  1. Why sedimentation matters in water treatment
  2. How the sedimentation process works, step by step
  3. Turbidity targets in Australian drinking water
  4. Types of sedimentation used in water treatment
  5. What sedimentation does not do
  6. Sediment in tap water at home
  7. Key takeaways
  8. Frequently Asked Questions
  9. Sources

Quick answer: Sedimentation is a gravity-driven step in water treatment where suspended particles settle to the bottom of a tank after coagulation and flocculation have clumped them together. It reduces turbidity before water moves on to filtration and disinfection, and it is one of the most widely used processes in municipal water treatment around the world.

How does sedimentation work in water treatment?

Why sedimentation matters in water treatment

Turbidity is the cloudiness or haziness of water caused by suspended particles such as clay, silt, algae, and organic matter. It is not just an aesthetic issue. High turbidity can interfere with disinfection, because particles shield microorganisms from chlorine and other disinfectants. That is why reducing turbidity early in the treatment process is a practical priority, not simply a cosmetic one.

The Australian Drinking Water Guidelines give a useful sense of scale: water with a turbidity of 5 Nephelometric Turbidity Units (NTU) appears slightly muddy or milky in a glass, while at 60 NTU it is not possible to see through the water at all. By contrast, what most people would describe as crystal-clear water usually has a turbidity of less than 1 NTU.

Sedimentation is the step that does much of the heavy lifting in bringing turbidity down from raw-source levels to something that filtration and disinfection can handle reliably.

How the sedimentation process works, step by step

Sedimentation does not work in isolation. It sits inside a sequence of treatment steps, and understanding those steps makes the process much clearer.

Step 1: Coagulation

Raw water entering a treatment plant carries fine suspended particles that are too small and too light to settle on their own. Many of these particles carry a slight negative electrical charge, which keeps them repelling each other and staying in suspension. Coagulation involves adding a chemical coagulant, most commonly aluminium sulfate (alum) or iron-based salts, to the water. The coagulant neutralises the electrical charge on the particles, allowing them to begin sticking together.

Step 2: Flocculation

After coagulation, the water is gently stirred in a flocculation basin. The slow, controlled mixing encourages the now-destabilised particles to collide and clump into larger, heavier masses called floc. Think of it as snowflakes forming from individual ice crystals: each collision builds a bigger, denser aggregate. The stirring must be gentle enough to encourage collisions without breaking the floc apart.

Step 3: Sedimentation (settling)

The flocculated water then flows into a large, calm sedimentation basin, sometimes called a clarifier or settling tank. Here, the water slows dramatically. With little turbulence to keep them suspended, the heavy floc particles sink under gravity to the bottom of the basin, forming a layer of sludge. The clarified water near the surface, now carrying far fewer suspended particles, flows over a weir or through an outlet at the top and moves on to the next treatment stage. The settled sludge is periodically removed and managed separately.

The efficiency of sedimentation depends on several factors: the size and density of the floc, the depth and surface area of the basin, the flow rate of water through the tank, and the temperature of the water (colder water is more viscous and slows settling).

Step 4: Filtration

Even after sedimentation, some fine particles remain. The clarified water passes through filtration media, typically layers of sand, anthracite, or granular activated carbon, to capture what sedimentation left behind. This brings turbidity down further before disinfection.

Step 5: Disinfection

Disinfection, usually with chlorine or chloramine, is the final barrier against microbial contamination. The Australian Drinking Water Guidelines state that a turbidity of less than 1 NTU is desirable at the time of disinfection with chlorine, unless a higher value can be validated in a specific context. This target reflects the practical reality that turbidity and disinfection effectiveness are directly linked.

Turbidity targets in Australian drinking water

Australian drinking water quality is guided by the Australian Drinking Water Guidelines, which set both aesthetic and operational turbidity benchmarks.

  • Aesthetic guideline: Turbidity should not exceed 5 NTU at the consumer's tap, based on aesthetic considerations.
  • Disinfection target: Less than 1 NTU is desirable at the point of disinfection.
  • Turbidity spikes: Short spikes in turbidity are considered best practice to limit to no longer than 15 minutes.

These figures reflect the dual role turbidity plays: it affects how water looks and tastes, and it affects how safely it can be disinfected. Treatment plants design their sedimentation and filtration stages around meeting both sets of targets.

Types of sedimentation used in water treatment

Not all sedimentation basins work the same way. Treatment plants use different designs depending on the volume of water they process, the characteristics of the source water, and the space available.

Conventional horizontal-flow basins

The most common design. Water flows horizontally through a long rectangular tank. Particles settle as the water travels from the inlet to the outlet. These basins are straightforward to operate and maintain, and they handle large volumes reliably.

Tube and plate settlers

These designs insert inclined tubes or plates inside the settling zone. The inclined surfaces dramatically increase the effective settling area within a smaller footprint. Particles settle onto the inclined surfaces and slide down into the sludge zone, while clarified water rises upward. Tube and plate settlers are often used to upgrade existing basins or where space is limited.

Dissolved air flotation (DAF)

For source waters with low-density particles, such as algae, that do not settle easily, dissolved air flotation works in the opposite direction to conventional sedimentation. Tiny air bubbles are introduced into the water and attach to floc particles, carrying them upward to the surface rather than letting them sink. The floating layer is then skimmed off. DAF is particularly common in Australian treatment plants drawing from reservoirs prone to algal blooms.

What sedimentation does not do

Sedimentation is highly effective at reducing turbidity and removing suspended solids, but it is one step in a multi-barrier treatment system, not a standalone solution. It does not reliably address dissolved contaminants such as chlorine, chloramine, fluoride, or dissolved heavy metals, because those substances are not suspended particles and do not settle under gravity. Filtration and disinfection stages handle different aspects of water quality, and together the full treatment train is designed to deliver water that meets Australian drinking water standards at the tap.

It is also worth noting that turbidity can fluctuate after treatment. Disturbances in distribution pipes, for example from pressure changes or maintenance work, can temporarily resuspend settled material. The Australian Drinking Water Guidelines note that it is considered best practice to limit short spikes in turbidity to no longer than 15 minutes.

Sediment in tap water at home

Municipal treatment plants work hard to deliver low-turbidity water, but sediment can still appear at the tap. Older pipes, local disturbances in the distribution network, or work on nearby mains can all introduce fine particles into household water. This is usually temporary and visible as a slight cloudiness or discolouration that clears after running the tap for a short time.

For households that want an additional layer of sediment reduction at the point of use, the Evolved H2O Advanced Tap Filter reduces over 150 common tap-water contaminants, including chlorine, PFAS, heavy metals, microplastics and sediment.

Key takeaways

  • Sedimentation uses gravity to settle suspended particles out of water after coagulation and flocculation have clumped them into heavier floc.
  • It is a core step in the multi-barrier treatment process used by Australian water utilities.
  • The Australian Drinking Water Guidelines set a turbidity target of less than 1 NTU at the point of disinfection and no more than 5 NTU at the consumer's tap.
  • Different basin designs, including horizontal-flow tanks, tube settlers, and dissolved air flotation, suit different source-water conditions.
  • Sedimentation addresses suspended particles; dissolved substances require separate treatment steps.

Frequently Asked Questions

What is the difference between sedimentation and filtration in water treatment?

Sedimentation uses gravity to settle large, heavy floc particles to the bottom of a basin. Filtration then passes the clarified water through media such as sand or activated carbon to capture finer particles that sedimentation left behind. The two steps work in sequence: sedimentation reduces the load on the filters, and filtration polishes what sedimentation started.

What is turbidity and how is it measured?

Turbidity is the cloudiness of water caused by suspended particles. It is measured in Nephelometric Turbidity Units (NTU) using a device called a nephelometer, which measures how much light is scattered by particles in the water. The Australian Drinking Water Guidelines note that water at 5 NTU appears slightly milky in a glass, while at 60 NTU it is not possible to see through the water.

Why does turbidity matter for disinfection?

Suspended particles can physically shield microorganisms from disinfectants such as chlorine, reducing the effectiveness of the disinfection step. The Australian Drinking Water Guidelines recommend turbidity of less than 1 NTU at the point of disinfection for this reason. Bringing turbidity down through sedimentation and filtration before disinfection is therefore an important part of the treatment sequence.

Does sedimentation remove dissolved contaminants like chlorine or fluoride?

No. Sedimentation works by settling suspended particles under gravity. Dissolved substances such as chlorine, chloramine, fluoride, and dissolved heavy metals are not particles and do not settle out. Removing or reducing dissolved contaminants requires different treatment steps, such as activated carbon filtration, ion exchange, or other point-of-use technologies.

Can sediment appear in tap water even after treatment?

Yes, occasionally. Disturbances in the distribution network, such as pressure changes or nearby pipe maintenance, can temporarily resuspend fine material in the pipes. This usually clears quickly. The Australian Drinking Water Guidelines note that best practice is to limit turbidity spikes to no longer than 15 minutes. If cloudiness persists, contacting your local water authority is a sensible step.

What is dissolved air flotation and when is it used instead of sedimentation?

Dissolved air flotation (DAF) is an alternative clarification process used when source water contains low-density particles, such as algae, that do not settle easily. Instead of sinking, particles are carried upward by tiny air bubbles and skimmed from the surface. DAF is common in Australian treatment plants drawing from reservoirs prone to algal blooms, where conventional sedimentation would be less effective.

Sources

Lachlan Movis, founder of Evolved H2O

Author Profile

Lachlan Movis

Founder, Evolved H2O

Lachlan Movis is the founder of Evolved H2O. He is passionate about helping Australian households make more confident water filtration choices. Through Evolved H2O, he shares practical guidance on water quality, filtration options, and everyday ways to improve the water you drink and use at home.

Lachlan Movis

About the author

Lachlan Movis

Founder, Evolved H2O

Lachlan Movis is the founder of Evolved H2O. He is passionate about helping Australian households make more confident water filtration choices. Through Evolved H2O, he shares practical guidance on water quality, filtration options, and everyday ways to improve the water you drink and use at home.

Not sure which filter you need?

Start with where you use water most.

Recommended for everyday drinking

3.5L Glass Water filter Jug

A thick glass filter jug with a bamboo lid and handle. No installation, just fill and pour.

Removes / reduces

  • PFAS (forever chemicals)Certain PFAS are linked to hormone, fertility, immune and liver effects, higher cholesterol and some cancers.
  • ChlorineLong-term exposure to certain chlorination by-products is linked to a higher risk of bladder cancer.
  • Unpleasant taste & odourMostly caused by chlorine and organic compounds, and a common reason people drink less water.
  • Sediment & everyday impuritiesRust and fine particles picked up in pipes can cloud water and affect its taste.
Learn more