HydroX Electric Water Filter

Use Your HydroX Electric Filter in 3 Simple Steps

No complicated setup. Fill, power on and dispense for clean, filtered water straight away. Full walkthrough below.

The full walkthrough

Set up your HydroX

Every day it's just three touches. The very first time, add one step: flush the new filter.

HydroX runs on municipal tap water. On well water, pre-filter first.

  • Fill the tank

    Fill with tap water up to (but not past) the MAX line. The tank holds 4.2 L (about 18 cups).

  • Power on

    Long press and hold both keys to switch the system on.

    Hold ◁ + ▷ · 3s
  • Flush the filterFirst use

    Activate the new cartridge before drinking. Press again to stop.

    Hold 💧 Dispense · 4s
  • Dispense

    Touch once and clean, filtered water pours straight into your glass.

    Tap 💧 Dispense · once

First time and after every filter change: discard the first 3 full tanks of filtered water and don't drink them. This clears carbon fines from the fresh cartridge.

Reading the display

What the lights mean

Touch any key to wake the unit first. The power indicator shows battery level; the filter light shows filter health.

  • Filter blue

    Filter is healthy, good to use.

  • Filter red

    Filter expired. Replace it soon, then hold a key 3s to reset.

  • White flashing

    Charging over USB-C. Solid white shows battery level.

  • Ready

    Powered on and ready to dispense.

Filter light red on a new unit? The filter timer is first set during manufacturing, so it can turn red earlier than expected. Hold a key for 3s until the light turns from red to blue to reset it.

Battery level reads in steps: 0 · 25 · 50 · 75 · 100%. A full charge lasts up to about 20 days of normal use.

At a glance

HydroX specifications

  • 6 months

    Filter life: up to 1,514 L

  • 4.2 L

    Tank volume (18 cups)

  • 0.65 L/min

    Rated flow rate

  • ~20 days

    Battery per charge · 4500mAh

  • USB-C

    5V / 2A · 8W

  • 1°C to 38°C

    Operating water temp

Filter replacement

When the light turns red, swap the filter

Filter light red = replace promptly.

HydroX Electric Water Filter refill cartridges for electric water filter pitcher
  1. Remove the filter cover.

  2. Unscrew the old cartridge anticlockwise; screw the new one in clockwise.

    A little water from the pump is normal.

  3. Reset the filter life

    Hold a key 3s until the light turns from red to blue.

  4. Flush the new cartridge

    Hold Dispense 4s, then discard the first 3 tanks.

Totally normal

If you notice any of these, you're fine

A few things surprise new owners. None of them mean anything's wrong.

  • Cloudy or milky water

    Tiny bubbles from the pump's pressure make water look cloudy for a moment. It clears on its own and is completely safe to drink.

  • TDS meter didn't drop

    By design. HydroX removes harmful substances while keeping beneficial trace minerals, so a TDS reading won't fall much. That's the minerals staying in.

  • Brief pause or noise on first flush

    That's air being purged from a fresh filter. It only happens at setup. If flow pauses, tap Dispense again to resume.

  • Shorter battery life

    Cold conditions, or keeping it in the fridge, can cut battery life by around half. More frequent dispensing also uses more charge.

No water or weak flow? Check it's charged, check there's water in the tank, and check the filter light isn't red. Any one of those is usually the cause.

Keep it fresh

Care & storage

  • Brush the tank monthly to prevent scale

  • No alcohol or solvents

  • Unused 7+ days: store the filter in the fridge

  • Charge at least every 3 months in storage

Need more detail?

Download the full manual

Full specifications, warranty terms and complete instructions for your HydroX.

Still stuck? Email us at info@evolvedh2o.com